What are Scheduled Maintenance Reminders?

Telematics Guru automatically calculates run hour and odometer estimates for each asset based on incoming device data. The Scheduled Maintenance Reminder (SMR) module allows jobs and maintenance schedules to be created for assets using this information. SMRs are particularly useful for large fleets that are centrally managed, as the automatic comparison of vehicle data against thresholds for servicing saves a lot of administration and head-space.

Schedule Types

Jobs can be run based on the following schedules:

Schedules can be based on a combination of the above i.e. every 6 months or 10 000kms, whichever comes first.

Unscheduled Jobs

Additionally, there is an unscheduled schedule type - designed for recording, actioning and tracking jobs that occur on an ad-hoc basis (i.e. repairing a cracked windscreen). These are jobs which are not regular. Completing jobs on these schedules doesn't automatically schedule a new job 10,000kms / 500hrs later etc. This type is not covered in this article, instead see Maintenance Lists.

Schedule Glossary

Create a Schedule

1. Go to Maintenance → Maintenance Schedules → Create New Schedule
    
2. Provide a name, supply some instructions and set the time zone.
   
   
    
3. Select the assets to be linked to the schedule
   
   
    
4. Configure email notifications by (1) selecting recipients from the address book. Then (2) indicating whether they should be notified when a job is about to be created. Next (3) choose whether the recipients will be notified when the job has been created.
   
   
    
5. Configure the schedule criteria.
   
   
   For each option, set the Action Interval, and Reminder period. 

Absolute Values/Dates

The above shows an absolute odometer value. So a job is generated on 10 000km, 20 000km, 30 000km etc If a job is generated on 10 000km, but we don't complete the job until 12 000km, the next job is still created at 20 000km.
If this was unchecked, the next job would be created relative to the previous - i.e. at 22 000km. The same applies to Calendar and Run Hours. 

Jobs and Reminders View

The Maintenance → Jobs and Reminders view is shown below. We can use this to view and action jobs and reminders.

1. Filter by asset
2. Filter by Schedule
   Using 1 and 2 we can view all jobs for a specific asset, or all jobs for a specific schedule.
3. Indicates if the item is a job or reminder
4. Click this to add a note for the upcoming job
5. We can action a reminder, either:
   1. Close the reminder - the job will still be generated when the the schedule elapses
   2. Create the job (create job now - maybe we want to action it)

Complete a Job

1. Set the date the job was completed
2. If desired, we can update the odo/run hours. Use case is sometimes the TG values and asset readings (i.e. the hour meter on the asset) may be slightly out of sync. This allows them to be aligned. 
3. If we are completing the job slightly early - if we should skip ahead to the next schedule.
4. Any notes. 

Document Upload

Documents can be uploaded to maintenance schedules when completing a job. 

This allows invoices, job sheets, photos and more to be captured against the maintenance schedule. Maintaining a complete history of all asset maintenance and documentation in one place. 

View Uploaded Documents

Once a job is completed and document uploaded, the history of documents is available on the Maintenance History of the asset (check “View Closed” in the Maintenance View) 

Maintenance Schedules View

We can also view the schedules via Maintenance → Maintenance Schedules. Schedules can also be edited from this view.

This view is equivalent to filtering the Jobs and Reminders schedule for All Assets and a specific schedule.

Reports

The Following Reports are available for schedule reminders; They allow you to list the Jobs and Reminders based on report parameters. It is recommended that you schedule the "Open Maintenance Jobs and Reminders" report to be emailed to a suitable person or group within your Organisation so that they will be proactively notified of new Jobs and Reminders that have been created in the system.

Add Asset To Schedule on Creation

When creating an asset, we can add the asset to the schedule directly on creation.

This saves needing to create assets and then visit the SMR page to update all schedules.