The Dart, Dart2, G62 and G100 all have immobiliser functions available. 


Note: Digital Matter does not advise connecting an immobilisation relay to a safety critical system such as the ignition or fuel pump. A starter motor cut is recommended.


This guide uses the Dart2 as an example, where there are differences, a link will be provided to the device.


For Driver ID options, see the article here


Immobilisation

  1. Telematics Guru Immobilise function
  2. Driver ID
  3. ASYNC message sent from server

Driver ID

  1. Scanning Driver ID Tags
  2. Drivers in Telematics Guru
  3. Driver Lists

Wiring Configurations


There are different ways to wire in a relay and configure the device settings to achieve a similar result.

However the aim is to try to avoid having the relay coil energised for an extended period of time - so as to not drain the vehicle battery if it is not driven for some time. 


There are 2 common use cases


  1. Default state is that the vehicle can always be started - unless via Telematics Guru or another software platform an 'immobilise' command is sent. In this case we want the relay when not energized to be closed, allowing the vehicle to start. Sending the command will energize the relay.

  2. The vehicle cannot be started until the right driver ID tag is scanned. In this case when the relay is not energized we want there to be a break in the start motor circuit.

Set up for immobilisation when a command is sent to the server.

The device's switched ground cable is attached to pin 85/Coil Negative and the starter motor connections to pin 30/Common and pin 87A/Normally Closed. 


The device will work as normal until the immobilise command is given.


This means when the immobilise function is activated in Telematics Guru, the starter motor is cut. This wiring configuration is used when you want the vehicle to operate as normal until you need to Immobilise.


Dart2 Wiring DiagramG62 Wiring DiagramG100 Wiring DiagramG120 Wiring Diagram



For the OEM Server system parameters, Add 'Digital Output 1' and set;

Function: Immobiliser

Active High: Yes


Set up in Telematics Guru for Immobilisation

To immobilise an asset in Telematics Guru, first navigate to Assets >> Manage Assets and edit the asset by clicking on the name, or selecting the checkbox and clicking on the cog menu on the right.


Select the Advanced tab in Edit Asset and check 'Can immobilise Asset' as shown below.


Once a device has been set up to allow immobilisation through the edit menu, simply click on the cog menu on the right of the Manage Assets screen, and select Immobilise.




Immobilisation via Driver ID

The device's switched ground cable is attached to pin 85/Coil Negative and the starter motor connections to pin 30/Common and pin 87/Normally Open.


This wiring method requires the correct Driver ID to be scanned before motor can start.


This means the Vehicle will not start unless the Driver ID is accepted. 


Dart2 Wiring DiagramG62 Wiring DiagramG100 Wiring DiagramG120 Wiring Diagram


Driver ID is available on the G62, Dart/2 and G100/G120.


To enable immobilisation without a valid Driver ID, the system parameter tab is named 'Driver ID' and the drop down box for Immobilise should be 'Yes' as shown below. The Digital output Parameter tab Function should also be set up for Immobiliser as shown below with Active High set to No




Async Messages

This wiring set up is the same as the Telematics guru wiring method.


Dart2 Wiring DiagramG62 Wiring DiagramG100 Wiring DiagramG120 Wiring Diagram


Async messages are used to send messages from the server to the device. These are used to:

  • Immobilise: enable or disable remotely
  • Set Digital Outputs: set or clear remotely
  • Trigger Accident Upload: trigger an upload of the accident data partition


These messages can only be sent to the device when it is connected to the server. Connections are triggered by the device. Triggers for the device to upload include:

  • On heartbeat: default is 60 min on the Dart. 
  • In trip: externally powered devices will do their best to stay connected. If ignition is on, the device is in trip by default.
  • On accident: device will do an upload
  • On digital input change: if the input is configured to “upload on change”, it will trigger a connection.
  • On tamper detection


The times when it is not connected, the message will not be delivered until the next connection. This includes:

  • After a trip end and upload, when the device is idle and sleeping
  • Between heartbeats, until the next upload trigger.
  • If the device cannot make a connection to the server because of network issues.

Driver ID

Scanning DriverID tags

After scanning a DriverID tag, the tag data will be forwarded to your end platform, or reported in OEM under Device logs if data capture is on.


It will also appear in TG Telemetry, Assets -> Telemetry

Setting up Drivers in Telematics Guru

Using the tag data you can create a new driver in TG from Admin > Drivers > New and fill out the details as below. 

The Driver ID tags that are available from Digital Matter are the Yellow DM RFID keyfobs and the blue iButton tags.

After adding the new driver details, you can assign the driver permission to drive a specific vehicle, or allow all enabled drivers in the Drivers tab in Edit Assets