Contact Us

If you still have questions or prefer to get help directly from an agent, please submit a request.
We’ll get back to you as soon as possible.

Please fill out the contact form below and we will reply as soon as possible.

  • Digital Matter Site
  • Contact Us

Dart2 - Getting Started

Written by Matthew Clark-Massera

Updated at October 2nd, 2023

Contact Us

If you still have questions or prefer to get help directly from an agent, please submit a request.
We’ll get back to you as soon as possible.

Contact Support
  • Home
  • Devices
  • Cellular
  • Hard-Wired
  • Dart3
  • Dart, Dart2

Table of Contents

digitalmatter.com Datasheet & High Resolution Images Dart 2 Downloads In the Box Setting it Up Inserting the Sim Card Remember APN AutoNet Connect the Battery Getting Online Opening and Closing the Housing Installation Location Note Wiring Diagrams Troubleshooting Steps

The Dart 2 is the new version of the Dart and is also a compact, economical and feature rich 2G or 4G tracking device.

It is designed to provide extremely cost effective tracking with all the quality and support of a Digital Matter product. It includes the latest GPS and cellular technology to give excellent performance at an entry level price. 

digitalmatter.com

See the Dart2 product page on www.digitalmatter.com for more specifications.

Datasheet & High Resolution Images

 Dart 2 Downloads

View the tech-specs and high resolution device images for the Dart2

This article will help you get up and running to test the Dart 2.

In the Box

You'll get a compact box containing the Dart 2 and a 12 wire harness. There are also OBDII and Cigarette Lighter harness options available for quick and easy (or temporary) installs. 

Setting it Up

Inserting the Sim Card

The Dart 2 uses a Micro SIM card–form factor 3FF. The SIM holder is on the top of the PCB. When handling the Dart 2 be careful not to touch the GPS antenna, to minimise the risk of damaging the sensitive GPS amplifiers with static discharge.

  • Unlock the SIM holder by sliding it towards the battery sideof the device. Open the holder up on its hinge.
  • Insert the SIM with the contacts down and the keyed corner pointing away from the battery side of the device
  • Put the holder back down on the PCB and slide it towards the closest side of the device to lock it in place.

To easily get up and running:

  • The SIM should not have a PIN on it, unless you use the device specific PIN.
  • The SIM should have credit or airtime

Remember

Make sure once you're online, you should Set the Network Profile (APN and bandmasks) for the best performance.

 

APN AutoNet

For more information on Declaring APNs and the 4G AutoNet,  see our knowledge base article here

Connect the Battery

The Dart 2 comes with a 200mAh battery

  • Leave the battery in the position it is stuck down, away from the antennas
  • Plug the battery into the socket shown in the image, positive (red) wire closest to battery.
  • The LED should start to flash.

Getting Online

Once the battery is connected, the internal LED will come on and flash red and the device will do the following:

If the SIM card works and there is sufficient charge in the battery, the device will connect to the OEM Server. Go to www.oemserver.com/installer and search for the serial number. Confirm that it has connected recently.

The LED will flash slowly at first. When it opens a connection to the server, it will flash fast. Once data is sent, it will go solid briefly, and revert to flashing fast. When the device goes to sleep, the LED will switch off.  
If the battery is too low, use the harness to provide external power.

If the LED flashes but the Dart does not connect, check the SIM is in the holder correctly and check that the SIM is working.

Opening and Closing the Housing

  • The housing closes with clips and does not need screws.
  • To close the housing, line up the top and bottom parts. Push the housing together firmly.
  • To open the housing, insert a flat screw driver into the opening highlighted below. Carefully lever the two halves apart.

Installation

Location

The housing has mounting holes for screws, bolts or cable ties. There are a few considerations for the final mounting position of DM devices. The devices have been engineered to have the best possible GPS reception. It will work from inside engine bays, body panels, under dashboards and other places where other GPS devices simply fail to operate reliably. Although the units will work in these locations it is always advisable to install them where it is best able to get signals from the GPS satellites, with the optimum position being a location with a clear 180-degree view of the sky. For more detail, see Where/how do I mount the device?

Note

The Dart, Dart2, G62 LTE & LoRaWAN and G100/G120 models all have 200mA fuses installed on the PCB for external power inputs. Digital inputs (including ignition) and switched ground outputs do not have integrated fuses, and are not specifically required by design, but may be installed to protect against external wiring faults.

The Fuses are self-resetting and do so when the fuse cools down. If the fault that is causing the fuse to trip is still present, it will require the device to be removed from power sources.

This means that the installer does not have to set up their own fuses for the device.

 

Wiring Diagrams

See:

  • Dart Wiring Diagrams
  • Wired Device Installation Guide

Troubleshooting Steps

See here for tips for if your device isn't connecting

Default Parameter Settings

The Dart 2 will operate with default settings out of the box. These can be changed using the OEM Admin interface. The defaults include:

  • Hourly Heartbeats: the device will log a heartbeat record, connect to the server, and refresh its GPS data every 60 minutes.
  • Logging: The device will log a record in trip every 60 seconds or 500m travelled. It will also log a record when the direction is changed by 10° and 150m is travelled with the new heading.
  • Wired AND Emulated Ignition: by default, the Dart will track a trip if either the ignition wire is pulled high or movement is detected. The setting can be changed to do one or the other, or continue to use both.
 
 

Default I/O Mappings

Digital Mappings Description
0 Ignition
5 GPS Interference
6 GPS Jamming
Analogue Mappings
Description
1 Battery Voltage
2 External Voltage
3 Device Temperature
4 GSM reception
 
 

Driver ID Options

The Dart2 has both iButton and TTL interfaces, which can be used to read a wide variety of Driver ID readers. See 

  • Driver ID Reader Options
  • Driver ID & Immobilisation methods with Powered Devices
 
 
dart2 dart 2 getting started start initial provision images spec setup set up online install

Was this article helpful?

Yes
No
Give feedback about this article

Related Articles

  • Dart Battery MSDS
  • Dart 3G Datasheet
  • Dart2 FAQ
  • Dart Wiring Diagrams

Subscribe to Partner News

Subscribe to our mailing list to receive Digital Matter news, product and tehnical updates, and more.

Subscribe

Copyright © Digital Matter . All Rights Reserved.

Privacy Contact Support

Knowledge Base Software powered by Helpjuice

Expand